(1) DTC80100FPR UPGRADE Power Amplifier Kit
features:
EXACT FIT & MOUNTING
Differential
Input Driver Protection
Output Clinching Speaker Protection
Fused
Dual Voltage Power Supply Rail Protection
Adjustable Input Gain Limit
Control
4 to 16 ohm Speaker Impedence
Up to 100 Watts
Output (depending on speaker loading, preamp
capabilities & gain adjustment)
Mounts
directly on the original circuit board locations using the
same stud patterns
RCA Phone Input Connection matches the
original signal input connector
Power Supply Connections (solder
pads) for use with the original DC Rails (+/-33vdc to +/-43vdc)
Speaker
Connections (solder pads)
Prewired Output Transistor
Harnesses with new TO3 sockets
Dual NPN TO3 Output Transistors
with mounting kits
Frequency Response: 20Hz to 25kHz
Audio Input
Signal: Up to 2.0V program
Precalibrated and
tested
Limited Warranty Replacement
Instructions
included
We use NPN Silicon High Power Output Transistors... no
more buying those pricy and hard to find PNP Germanium
transistors!
Note: Most Suitcase Amplifier designs use (2)
power amplifiers. We recommend replacing both!
DTC80100FPR Power Amplifier (new pricing for
2010!)
The DTC4070PAS custom
designed & handcrafted exact fit UPGRADE power amplifier for
the
LESLIE™ SOLID STATE TONE
CABINETS!
Part Number: DTC4070PAS (Single Upgrade Power
Amplifier)
(1) DTC4070PAS UPGRADE Power Amplifier Kit
features:
EXACT FIT &
MOUNTING
Differential Input Driver Protection
Output Clinching
Speaker Protection
Fused Dual Voltage Power Supply Rail
Protection
Adjustable Input Gain Limit Control (accessable thru
original back panel hole, some Leslie models may require
drilling)
4 to 16 ohm Speaker Impedence
Up to 100 Watts
Output (depending on speaker loading, preamp output & gain
adjustment)
Mounts Directly in original circuit board locations using
the same stud patterns
Input Connection matches the original 1 pin
plug-in
Power Supply Connection matches the original 5 pin
plug-in
Speaker Connection matches the original 2 pin
plug-in
Prewired Output Transistor Harnesses with new TO3
sockets
Dual NPN TO3 Output Transistors with mounting
hardware
Frequency Response: 20Hz to 25kHz
Audio Input Signal: Up to
2.0Vac program
Precalibrated and tested
Limited Warranty Replacement
Installation Instructions
included
Note: Some
LESLIE™ Solid State Tone Cabinets may have more than (1) power
amplifier. We recommend replacing all of them!
Check our CROSS REFERENCE
page to see how many power amplifiers your model actually
contains.
DTC4070PAS Power
Amplifier (new pricing for
2010!)
ADD MORE POWER WITH OUR
DTC4070BA BUMP AMP SERIES BELOW!
NOTE: A basic knowledge of solid state electronics and
HAMMOND/LESLIE® speaker cabinets are required for proper
installation.
We recommend that all installations of our products be
performed by qualified electronic technical services
personnel.
Just a little more output please!
Consider adding one of the following BUMP AMPS to
your DTC4070PAS power amplifier.
(NOTE: increased output wattage depends on
the original power supply capabilities!)
Some LESLIE models may have additional space
available on the METAL BACK PANEL
that would allow for mounting our SHORT
MOUNT style Bump Amp right along side or
above and below our DTC4070PAS
Power Amp. Drilling the Back Panel for our base plate
will be required.
Part Number: DTC4070BASRM (Short Remote
Mount Kit with 24 inch wire
harness)
For Remote
Mounting Inside the Leslie Cabinet
Bumps our DTC4070PAS power amp to maximum wattage.
(NOTE: increased output depends on original power supply
capabilities!)
FOR USE
WITH HIGH-POWERED SPEAKERS ONLY!
Our DTC4070BASRM BUMP AMP Kit
features:
Quick
Connect 24 inch Wire Harness to our DTC4070PAS Power Amplifier
Series
Insulated Standoffs & Cable Supports
Aluminum Base
Plate with Mounting Hardware
Precalibrated and tested
Limited
Warranty Replacement
Installation Instructions
included
DTC4070BASRM Bump Amp (new pricing for
2010!)
NOTE: A basic knowledge of
solid state electronics and HAMMOND/LESLIE® speaker cabinets are required
for proper installation.
We recommend that all installations of our products
be performed by qualified electronic technical services personnel.
We
recommend increasing the capability of the Leslie power supply to achieve the
full bump amp wattage available.
Other
LESLIE models may only have room available along the side walls of the
wood
cabinet or in the upper speaker compartment or even the removable wood
back
panel of the upper compartment. For this situation we offer our
LONG REMOTE MOUNT
style for use with our DTC4070PAS Power
Amp.
Part
Number: DTC4070BALRM
(Long Remote Mount Kit with 48 inch wire
harness)
For Remote Mounting Inside the Leslie Cabinet
Bumps our DTC4070PAS power
amp to maximum wattage. (NOTE: increased output depends on the
original power supply capabilities!)
FOR USE WITH HIGH-POWERED SPEAKERS
ONLY!
Our
DTC4070BALRM BUMP AMP Kit features:
Quick Connect 48 inch Wire Harness to our
DTC4070PAS Power Amplifier Series
Insulated Standoffs & Cable
Supports
Aluminum Base Plate with Mounting Hardware
Precalibrated and
tested
Limited Warranty Replacement
Installation Instructions
included
DTC4070BALRM BUMP AMP (new pricing for
2010!)
NOTE: A basic
knowledge of solid state electronics and HAMMOND/LESLIE® speaker
cabinets are required for proper installation.
We recommend that all
installations of our products be performed by qualified electronic
technical services personnel.
We recommend increasing the capability of the
Leslie power supply to achieve the full bump amp wattage
available.
amplifiers,amplifiers,amplifiers,solid state,solid state,solid state,tube,tube,tube, guitar,guitar,guitar,bass,bass,bass,keyboard,keyboard,keyboard,organ,organ,organ,stage,stage,stage,lighting,lighting,lighting, systems,systems,systems,vintage,vintage,vintage,classic,classic,classic,leslie,leslie,leslie,solid,solid,solid,state,state,state, tone,tone,tone,cabinet,cabinet,cabinet,fender,fender,fender,rhodes,rhodes,rhodes,piano,piano,piano,suitcase,suitcase,suitcase, peterson,peterson,peterson,amp,amp,amp